7 DIY Plumbing Mistakes – How NOT to Plumb

There are a number of common mistakes that DIY enthusiasts make. Here are the top plumbing mistakes that you should avoid.

1Not having the appropriate tools.

So, you have finally decided to tackle that plumbing job in your home, surely it can’t be that hard, can it? You’ve dug out the trusty toolbox. Inside are a set of mole grips, a bent screwdriver that doubles as a chisel, a rusty tape measure with half the numbers missing and a blunt hacksaw.

These kinds of tools will not get you far and will most certainly hinder your chances of completing the job with ease.

Before you undertake any plumbing job be sure to check you have the correct tools for the job. Adjustable spanners, pump pliers, a descent screwdriver set, tape measure and a well-made hacksaw would be the bare minimum.

2Over tightening plumbing fittings and pipe connections.

Over tightening plumbing fittings, whether plastic, brass, copper, or iron can cause serious problems. Over tightening a plastic waste fitting can cause the nut to slip. Over tightening on an iron thread can cause the fitting to split. Both scenarios will cause a leak and damage the pipe or fitting completely.

3Tightening an olive joint dry.

There is this saying, they don’t make them like they used to. Well this certainly stands for plumbing olives. Depending on the supplier, some plumbing compression fittings come with copper olives. Copper olives are softer than brass and can be over squashed with ease.

To avoid over tightening and that horrible screeching noise when over tightening a compression joint, use a jointing compound on the olive. Pipe joint compound, also known as pipe dope, is a type of sealant or paste used to help create a water tight seal.

4Using chemical drain unblocker as a first choice.

The first thing most people do when their plughole is clogged is head to the shop and pick up some chemical drain cleaner. Easy solution, right? Wrong. It is much easier to remove and clear the trap, use a drain snake, drain cleaning tool or plunger.
The chemicals used in drain unblockers, especially the cheaper ranges, are highly toxic and bad for the environment. Because the chemicals used in drain unblockers are so strong, these cleaners can cause damage to your drainage system, corroding pipes and fittings.

To clear a slow drain, sprinkle it with baking soda, then pour in vinegar and leave the solution to sit for several hours. When you’re done, flush it with hot water.

5Using inappropriate taping methods or wrapping a thread tape backwards.

PTFE thread tape must wrap clockwise around the thread joint for it to work properly. Many DIYers make the mistake of wrapping it backward so the tape unwinds from the threads as they tighten the fitting. That defeats the whole purpose of using thread tape since it can’t seal if it isn’t embedded in the threads.

One other common mistake is putting the PTFE tape on the thread of a compression fitting. This serves no purpose whatsoever and is the improper use of PTFE tape. Yes, the joint will still leak.

To seal a compression olive joint, use a plumbing joint compound or paste (not silicone or PTFE)

6Not using plastic pipe inserts with MDPE or hep20

What’s so special about pipe inserts anyway? Pipe inserts play an especially important role in providing extra support to plastic pipework minimising any loss of shape that can occur when cutting.

Pipe inserts maintain the structural shape of the pipework, providing a more effective seal between the outside diameter of the pipe and the O-ring. In turn, this helps to make the pipe more rigid when a fitting is applied.

7Not replacing the chemical inhibitor after draining a heating system.

So, what is radiator inhibitor and why is it so important?

Central heating inhibitor is a chemical liquid used to protect your central heating system and keep it working efficiently and prolong its lifespan.

Over time, radiator sludge builds up in your central heating system. This thick black or brown gloop sits at the bottom of your pipes and radiators which stops the water running through your system properly, putting strain on your boiler and causing your radiators to not heat up efficiently.

The chemicals in the inhibitor break down the sludge in your central heating system and protects it from building up again.

2 thoughts on “7 DIY Plumbing Mistakes – How NOT to Plumb”

Leave a Reply

Your email address will not be published. Required fields are marked *